SEA MAKER (SEA TREATMENTS)

Stok Kodu: 0
Açıklama:

  1. INLET&OUTLET WATER CHARACTERIZATION

 

The consumption is the amount of water that needs to be replaced in the water circuits installed. The source of the water will supply from Water Treatment Plant.

 

1.1.      Waste Water Treatment Plant Inlet

 

      1. Well Water Analyses

 

Parameter

Unit

 Value

Choloride

mg/lt  Cl/L

  6000

Conductivity

µS/cm

  44.200

 pH

   -

7,66

  Turbidity

  NTU

  0,53

   Sulfate

  mg SO4/L

  2800

   Calcium

  mg Ca/L

   69,9

   Total Hardness

  ppm

  2800

 

  1. RO Permeate Water Parameters

 

Parameter

Unit

 Value

Choloride

mg/lt  Cl/L

  120

Conductivity

µS/cm

  1000

 pH

   -

6,5

  Turbidity

  NTU

  0,1

   Sulfate

  mg SO4/L

  70

   Calcium

  mg Ca/L

  20

   Total Hardness

  ppm

  40

 

 

2. PROCESS UNITS

 

EQUIPMENT SPECIFICATIONS

 

    1. RAW WATER FEED & BACKWASH PUMP

Amount

2 unit

Brand

BIOCLEAN

Material

Duplex Steinless Steel

Power Supply

380 V, 50 Hz, 3 phase

Material

ST 37

 

 

 

 

 

 

 

 

 

 

    1. ACID DOSAGE UNIT

Dosage Pump

Amount

1 unit – on/off control

Brand

BIOCLEAN

Solution

HCL

Power Supply                   

220 Volt 50 Hz

Solution Tank

Capacity

50 L

Amount

1 unit

Material

Polyethylene

 

 

    1. SMBS DOSAGE UNIT

Dosage Pump

Amount

1 unit – on/off control

Brand

BIOCLEAN

Solution

SMBS

Power Supply                   

220 Volt 50 Hz

Solution Tank

Capacity

250 L

Amount

1 unit

Material

Polyethylene

 

 

    1. ANTISCALANT DOSAGE UNIT

Dosage Pump

Amount

1 unit – on/off control

Brand

BIOCLEAN

Solution

Antiscalant

Power Supply                   

220 Volt 50 Hz

Solution Tank

Capacity

250 L

Amount

1 unit

Material

Polyethylene

 

 

    1. FULLY AUTOMATIC MULTIMEDIA FILTRATION SYSTEM

 

 Multimedia Filtration Systems are used both as a preliminary system for the treatment of process water and the elimination of the blurriness of water obtained from water treatment systems. Ekosistem fully automated multimedia filtration systems cleanse coarse residue, particles, suspended solid matter, and materials that cause blurriness in industrial and commercial applications to make your water useable.

 

Ekosistem specific blended multimedia filters with 20-micron filtration sensitivity with less pressure loss through the filter and longer filter runs. Specially blended filters prevent a rapid buildup of head loss and blinding problems that are associated with typical sand filters.

 

Amount

1 Set

Model

MMF-63-E

Actuator Type

Electric Actuator Valve

Valve Brand

STARVALVE or eqv.

Valve Body Material

Cast Iron

Valve Amount

5 pieces Actuator per unit

Automation

PLC Controlled (common automation)

Inlet / Outlet line connection diameter

1”

Distribution type of inside the tank

PVC Diffuser

Piping Material

PVC

Filtration Section Speed

10 m/h

Backwash Duration

15 - 25 min.

Backwash Period

Timer-controlled backwash system.

Backwash Material

With water

Tank operation pressure

4 - 6 bar

Pressure drop                                  

0,5 – 1 bar

Power

220 V / 50 Hz

Operating Temp.

5–50 ° C

 

    1.  1ST PASS REVERSE OSMOSIS

 

Equipment Description

Technical Data

Quantity

Capacity

Model

Others

1ST PASS REVERSE OSMOSIS SYSTEM

1st Pass Reverse Osmosis System

1 Duty

30 m3/d

 

Recovery: 15%

Cartridge Filter

2 Duty

-

Ekosistem

PVC Body             5 – 1 micron

High-Pressure Pump (VFD)

1 Duty

10 m3/h

Danfoss

316 Stainless Steel

Membranes

10 Duty

-

Torray&CSM&Filmtech

8" Dia; 40"Length

Membrane Vessel

1 Set

-

PROTEC or equivalent

 

Conductivity Analyser & Sensor

1 Set

-

GF+ & Siemens

Feed and Product Water Line

pH Analyser & Sensor

1 Set

-

Swan/ GF+/Seko

Feed Water Line

Flowmeter

1 Set

-

Siemens/GF+

Feed and Concentrate Water Line

ORP Analyser & Sensor

1 Set

-

Swan/GF+/Seko

Feed Water Line

Pressure Gauge

1 Set

-

Pakkens

Cartridge filter, high-pressure pump, and stage inlet and outlets

Temperature Transmitter

1 Set

-

GF+

Feed Water Line

Pressure Transmitter

1 Set

-

Siemens&Keller

Product, Concentrate Water Line, and interstage

Low-Pressure Switch

1 Set

-

Danfoss

High-Pressure Pump Suction Line

High-Pressure Switch

1 Set

-

Danfoss

High-Pressure Pump Discharge Line

Automatic Flushing Unit

1 Duty

-

-

Drain Line

Skid

1 Duty

-

-

Carbon Steel

 

  1. CONNECTION EQUIPMENT

 

Low Presssure PE High Pressure Duplex Steinless Steel

 

  1. STEEL CONSTRUCTION EQUIPMENT

 

Machine base, mixer chassis, equipment feet, and pipe assembling.

 

  1. DELIVERY TIME

The works under our proposal will be done according to the following business schedule. The duration of the supply of mechanical equipment and construction works will be carried out as of the same months. 

 

Construction of Settlement, Process, and Electricity Projects

  1 Weeks

Mechanical and Electrical Equipment Supply

  6 Weeks

Assembly Works

Commissioning

  1 Weeks

  1 Day

 

 

 

 

 

     

 

  1. EQUIPMENT WARRANTY

 

Equipment and fittings will comply with German DIN and/or TSE standards.

Galvanized coating and surface protection suitable for the process will be made on the required surfaces.

The local supply to be used in the system is under our warranty for (one) year after all equipment (except electric motors) is delivered.

Warranty conditions do not cover situations contrary to the operation-maintenance instructions.

 

  1. SUPERVISOR

 

The supervision fee is 650 USD/person for day.

 

  1. PROCESS GUARANTEE

Our process warranty applies to the values given in Table 1.

 

  1. PRICE

 

  1. Foreign exchange prices will be converted into TL at the effective selling rate of the Central Bank on the date of payment and will be paid in advance.
  2. Equipment invoice sent in material delivery will be issued.
  3. If transportation cannot be made due to problems arising from the buyer on the material delivery date, the buyer or the representative of the buyer will be shown that equipment and devices are available in the workshop and payment will be made in advance within 15 days.
  4. If this date is extended due to problems arising from the buyer in the contract, the start date of the installation will be made in cash within 15 days at the latest.

 

 

 

  1. TERMS OF PAYMENT

%50    Advance payment with signing the contract,

%40    Before Material Delivery + Total VAT price by bank transfer,

%10    After Installation Completed

 

 

Our prices include all jobs covered by the offer.

 

1. OPTION

Our offer is valid for 1 month.

 

WhatsApp
Hemen Ara